D0 隔离开关熔断器组（母线式安装） (31525)

The picture may show a similar product.

说明

订货号 31525000

SECUR^®60Classic PowerLiner

D0 隔离开关熔断器组（母线式安装）

适用于 D01 和 D02 熔断器，带 LED

E18 / 63 A / 3 极

下端接电缆

适用母线 12, 15, 20, 25, 30 x 5, 10 和异型母线

3-pole / 1-pole switching

系统

60Classic

产品组	01
分组	42

包装件数	1
EAN	4021267315252

产品手册页码

2020 : 3.18

ECLASS 6.1	27142110
ECLASS 7.1	27142110
ETIM 4.0	EC000277
ETIM 5.0	EC000277

认证

标准

IEC 60947-1:2020
IEC 60947-3:2020 AC ratings only

认证许可

VDE , CCC , DNV GL , EAC

型号: SPL-D0

EAC Type: D0

CCC认证: 2018010302128773

产品信息

for fuse links size:	D0
fuse links acc. to standard:	IEC / HD 60269-3
所使用熔断器的允许损耗功率:	5.5 W
requirements for contact parts:	Fuse links with silver-plated contact pieces recommended. For fuse links with nickel-plated contact pieces, a reduction factor of 0.8 is to be observed.

Details IEC
标准
IEC 60947-1:2020 IEC 60947-3:2020 AC ratings only

Electrical data IEC
额定电流（IEC）:	63 A
额定电压（IEC）AC:	400 V

额定电压（IEC） DC:

110 V

rated isolation voltage U_i AC:	500 V
额定绝缘电压 U_i DC:	250 V
额定冲击耐受电压 U_imp:	6 kV

使用等级 AC (IEC 60947-3):	AC-23A (400 V)
使用等级 DC (IEC 60947-3) :	DC-21B (48 V1极l DC-21B (110V) 2极

带熔断器时的条件额定短路电流:	50 kA / 400 V
带熔断器测定的工作等级:	gG

功率输出:

The power dissipation at a typical load of 80 % results to 6.7 W.

(The power dissipation at full load would be 10.5 W.)

Supplementary data IEC
下述参数已经在特定条件下通过测试得到验证。开始设计之前，请联系维纳尔咨询这些条件。

符合 IEC 60947-3 的熔断器组合电器，只有在作为没有分断能力的熔断器式隔离器时、在不超过额定绝缘电压使用并进行相应的标识时，才允许超过额定工作电压运行。

熔断器故障时LED灯闪烁工作范围: 110 - 400 V AC / DC
for fuse links and gauge rings as per DIN VDE 0636-3 IEC / HD 60269-3 utilisation category as per VDE 0638: AC22
进线和出线连接之间的分隔功能需根据产品标准对开关机制的开口要求来确定当开关机构闭合和取出熔断器时, 母线和接线端子之间产生的电势能穿过LED。

机械数值
宽 x 高 x 厚:	27 x 220 x 100
重量:	76.5 kg/100
极数:	3线
适用母线:	12, 15, 20, 25, 30 x 5, 10 和异型母线

正面防护等级:

IP20

Type of fastening: patented click mechanism

连接端
cage clamp connection
screw drive:	PZ2
wire stripping:	12 mm
min. cross-section:	1.5 mm²
最大横截面积:	16 mm²
Md min.:	2.5 Nm
Md max.:	3.0 Nm
Not suitable for aluminium cables !

说明

SECUR®PowerLiner can be fitted with D0 adapter sleeves. With reducer insert (part no. 31902) and adapter sleeves, also suitable for D01 fuse-links. The use of the side module part no. 31901 is recommended for continuous loads of 35 A or greater.

LED lights when the fuse-link trips or is missing

use D02 fuse-links with silver plated end caps